Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

maintenance profile

Matronics Email Lists Forum Index -> RV10-List

View previous topic :: View next topic

Author Message

dlm34077(at)q.com
Guest

Posted: Mon Feb 20, 2012 6:04 pm Post subject: maintenance profile

Anyone have any numbers yet on time between main tire replacement and brake lining replacement?  

       [quote][b]

thane

Joined: 27 Nov 2006
Posts: 56

Posted: Tue Feb 21, 2012 5:19 am Post subject: maintenance profile

I made around 275 hrs. on brakes, but one pad was  just barely serviceable, wont go that long again.  My tires are still good  at 308 hrs. My new landing procedure will be to roll out more, save some  brakes.

  

 Thane States

 N321BY

 RV-10

 [quote]   ---

_________________
Working on finish kit: I hate fiberglass!!

Mauledriver(at)nc.rr.com
Guest

Posted: Tue Feb 21, 2012 6:14 am Post subject: maintenance profile

I had the same situation on my old Maule, that is, the tires would     wear on the outside and would require flipping to get full wear.

     

     I assumed it was because when the gear was unloaded, the gear legs     would swing inward somewhat.  On landing, the outside of tires would     contact the runway first.  That's when then would spin up from 0 to     50, and it's also when any misalignment would be 'scrubbed off'.  I     figured it was when the most wear was put on the tires.

     

     Is this what may be happening with our '10s?

     

     BTW, thanks for the maintenance profile question and the feedback -     good stuff.

     

     Bill Watson

     [quote]

       We are using the brakes less and getting better life out of the       pads.  Tires would last longer if Vans had changed the tire camber       on the wheels.  Wearing the outside of the main tires seems like       something they would have an interest in fixing.

       

       Jim Combs

       N312F - 350+ Hours

        

       

        	  Quote: 	
		  

	
     [b]

coop85(at)verizon.net
Guest

Posted: Tue Feb 21, 2012 6:23 am Post subject: maintenance profile

For what it's worth, time between replacements on things like tires and brakes are going to depend a lot on what kind of flying you do.  Lots of landings equals wear and tear on the tires and brakes, in addition to technique, rather than time.  My tires started lasting a LOT longer once my flights were more of the 4 hour type than beating up the landing pattern.  My point is simply this sort of data is going to vary a lot between users so may not be of as much help as number of landings, which most folks don't track in their maintenance logs.  Having said that, it still might be useful as most of us use the airplane for cross-country so the info might be more consistent after all.  Time for more coffee, that was a lot of rambling, sorry.



Marcus 

do not archive



On Feb 20, 2012, at 9:00 PM, DLM wrote:

Anyone have any numbers yet on time between main tire replacement and brake lining replacement?



 	  Quote: 	
		  



style="color: blue; text-decoration: underline; ">http://www.matronics.com/Navigator?RV10-List

blue; text-decoration: underline; ">http://forums.matronics.com

style="color: blue; text-decoration: underline; ">http://www.matronics.com/contribution



	




 [quote][b]

pietflyr(at)bellsouth.net
Guest

Posted: Tue Feb 21, 2012 6:41 am Post subject: maintenance profile

My RV-4 does the same thing, as did my Cessna 140.  This is simply a characteristic of spring type landing gear.  They are designed for the wheels to have proper camber when carrying the weight of the airplane.  As Bill pointed out, the maximum wear occurs when they are pretty much unloaded.  If the gear were designed for the tires to touch down level, when the gear was loaded with the airplane’s weight they would be wrong and the plane would be difficult to control on the ground.    

   

If you want to have it both ways, you need gear like my Pietenpol has:  

   

[img]cid:image001.jpg(at)01CCF07C.B7A952C0[/img]  

   

Jack Phillips  

#40610 Wings (Flaps)  

Raleigh, NC  

         

  

From: owner-rv10-list-server(at)matronics.com [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Bill Watson

 Sent: Tuesday, February 21, 2012 9:12 AM

 To: rv10-list(at)matronics.com

 Subject: Re: RV10-List: maintenance profile  

  

   

I had the same situation on my old Maule, that is, the tires would wear on the outside and would require flipping to get full wear.

 

 I assumed it was because when the gear was unloaded, the gear legs would swing inward somewhat.  On landing, the outside of tires would contact the runway first.  That's when then would spin up from 0 to 50, and it's also when any misalignment would be 'scrubbed off'.  I figured it was when the most wear was put on the tires.

 

 Is this what may be happening with our '10s?

 

 BTW, thanks for the maintenance profile question and the feedback - good stuff.

 

 Bill Watson

 

   



 We are using the brakes less and getting better life out of the pads.  Tires would last longer if Vans had changed the tire camber on the wheels.  Wearing the outside of the main tires seems like something they would have an interest in fixing.

 

 Jim Combs

 N312F - 350+ Hours

     	  Quote: 	
		     	
  

    	  Quote: 	
		     	
0 	  Quote: 	
		   	
1 	  Quote: 	
		   	
2 	  Quote: 	
		   	
3 	  Quote: 	
		   	
4 	  Quote: 	
		   	
5 	  Quote: 	
		   	
6 	  Quote: 	
		   	
7 	  Quote: 	
		   	
8 	  Quote: 	
		   	
9 	  Quote: 	
		   	
0 	  Quote: 	
		   	
1 	  Quote: 	
		   	
2

image001.jpg

Description:

Filesize:

51.29 KB

Viewed:

5257 Time(s)

coop85(at)verizon.net
Guest

Posted: Tue Feb 21, 2012 7:47 am Post subject: maintenance profile

Jack...Gorgeous airplane!  Looks like a lot of fun.  I've been toying with doing something like that as well for just buzzing around which the -10 has proven to be a bit expensive for thanks to current gas prices.



Marcus

do not archive



On Feb 21, 2012, at 9:39 AM, Jack Phillips wrote:

My RV-4 does the same thing, as did my Cessna 140.  This is simply a characteristic of spring type landing gear.  They are designed for the wheels to have proper camber when carrying the weight of the airplane.  As Bill pointed out, the maximum wear occurs when they are pretty much unloaded.  If the gear were designed for the tires to touch down level, when the gear was loaded with the airplane’s weight they would be wrong and the plane would be difficult to control on the ground. 

 

If you want to have it both ways, you need gear like my Pietenpol has:

 

<image001.jpg>

 

Jack Phillips

#40610 Wings (Flaps)

Raleigh, NC

 



From: owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com) [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Bill Watson

Sent: Tuesday, February 21, 2012 9:12 AM

To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)

Subject: Re: maintenance profile



 

I had the same situation on my old Maule, that is, the tires would wear on the outside and would require flipping to get full wear.



I assumed it was because when the gear was unloaded, the gear legs would swing inward somewhat.  On landing, the outside of tires would contact the runway first.  That's when then would spin up from 0 to 50, and it's also when any misalignment would be 'scrubbed off'.  I figured it was when the most wear was put on the tires.



Is this what may be happening with our '10s?



BTW, thanks for the maintenance profile question and the feedback - good stuff.



Bill Watson





We are using the brakes less and getting better life out of the pads.  Tires would last longer if Vans had changed the tire camber on the wheels.  Wearing the outside of the main tires seems like something they would have an interest in fixing.



Jim Combs

N312F - 350+ Hours

  	  Quote: 	
		     	
 

 	  Quote: 	
		    http://www.matronics.com/Navigator?RV10-List 	
0 	  Quote: 	
		   	
1 	  Quote: 	
		   	
2 	  Quote: 	
		   	
3 	  Quote: 	
		   	
4





 [quote][b]

scottmschmidt(at)yahoo.co
Guest

Posted: Tue Feb 21, 2012 9:29 am Post subject: maintenance profile

Here were my numbers on the stock tires and brake pads. Like others have said, I am getting better wear now that I have more time on the plane.  With Dresser re-treads, they will last much longer than the stock tires from Vans.  



http://www.vansairforce.com/community/showthread.php?p=149271#post149271



 

Scott Schmidtscottmschmidt(at)yahoo.com



 	  Quote: 	
		          From: Marcus Cooper <coop85(at)verizon.net>

 To: rv10-list(at)matronics.com 

 Sent: Tuesday, February 21, 2012 8:45 AM

 Subject: Re: maintenance profile

  

 

 Jack...Gorgeous airplane!  Looks like a lot of fun.  I've been toying with doing something like that as well for just buzzing around which the -10 has proven to be a bit expensive for thanks to current gas prices.



Marcus

do not archive



On Feb 21, 2012, at 9:39 AM, Jack Phillips wrote:

My RV-4 does the same thing, as did my Cessna 140.  This is simply a characteristic of spring type landing gear.  They are designed for the wheels to have proper camber when carrying the weight of the airplane.  As Bill pointed out, the maximum wear occurs when they are pretty much unloaded.  If the gear were designed for the tires to touch down level, when the gear was loaded with the airplaneâ€™s weight they would be wrong and the plane would be difficult to control on the ground. 

  

If you want to have it both ways, you need gear like my Pietenpol has:

  

<image001.jpg>

  

Jack Phillips

#40610 Wings (Flaps)

Raleigh, NC

  



From: owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com) [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Bill Watson

Sent: Tuesday,  February 21, 2012 9:12 AM

To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)

Subject: Re: maintenance profile



  

I had the same situation on my old Maule, that is, the tires would wear on the outside and would require flipping to get full wear.



I assumed it was because when the gear was unloaded, the gear legs would swing inward somewhat.  On landing, the outside of tires would contact the runway first.  That's when then would spin up from 0 to 50, and it's also when any misalignment would be 'scrubbed off'.  I figured it was when the most wear was put on the tires.



Is this what may be happening with our '10s?



BTW, thanks for the maintenance profile question and the feedback - good stuff.



Bill Watson



We are using the brakes less and getting better life out of the pads.  Tires would last longer if Vans had changed the tire camber on the wheels.  Wearing the outside of the main tires seems like something they would have an interest in fixing.



Jim Combs

N312F - 350+ Hours

 

 	  Quote: 	
		        	
  

 	  Quote: 	
		      http://www.matronics.com/Navigator?RV10-Listhttp://forums.matronics.com  	
0 	  Quote: 	
		    	
1 	  Quote: 	
		    	
2 	  Quote: 	
		    	
3





  	  Quote: 	
		    	
4

Bob Turner

Joined: 03 Jan 2009
Posts: 885
Location: Castro Valley, CA

Posted: Tue Feb 21, 2012 12:24 pm Post subject: Re: maintenance profile

So....is anyone removing their tires before the wear is too extreme, and flipping them 180 degrees? Or keeping the orientation the same and moving from left to right side? So the worn part is now on the inside.



Bob

_________________
Bob Turner
RV-10 QB

jesse(at)saintaviation.co
Guest

Posted: Tue Feb 21, 2012 12:38 pm Post subject: maintenance profile

Definitely. It always wear on the outboard side of the tire, so you get almost double life if you flip them.



Jesse Saint

Saint Aviation, Inc.

jesse(at)saintaviation.com

C: 352-427-0285

F: 815-377-3694



On Feb 21, 2012, at 3:24 PM, Bob Turner wrote:



 	  Quote: 	
		   

 

 So....is anyone removing their tires before the wear is too extreme, and flipping them 180 degrees? Or keeping the orientation the same and moving from left to right side? So the worn part is now on the inside.

 

 Bob

 

 --------

 Bob Turner

 RV-10 QB

 

 

 

 

 Read this topic online here:

 

 http://forums.matronics.com/viewtopic.php?p=366877#366877

Tim Olson

Joined: 25 Jan 2007
Posts: 2878

Posted: Tue Feb 21, 2012 12:41 pm Post subject: maintenance profile

I wait until there is no groove on the outside

tread groove...then flip it on the rim and use the

other side of the tire.  Even when there's a lot of

wear there, it works out ok because you just don't

use the inside of the tire much at all.

Tim

On 2/21/2012 2:24 PM, Bob Turner wrote:

 	  Quote: 	
		   

 Turner"<bobturner(at)alum.rpi.edu>



 So....is anyone removing their tires before the wear is too extreme,

 and flipping them 180 degrees? Or keeping the orientation the same

 and moving from left to right side? So the worn part is now on the

 inside.



 Bob



 -------- Bob Turner RV-10 QB

John Ackerman

Joined: 19 Jun 2006
Posts: 130
Location: Prescott, AZ

Posted: Wed Feb 22, 2012 9:21 am Post subject: maintenance profile

Flipped them at inspection time - about 80 hrs. Appreciably more wear on outside.

John Ackerman

40458



On Feb 21, 2012, at 1:24 PM, Bob Turner wrote:



 	  Quote: 	
		   

 

 So....is anyone removing their tires before the wear is too extreme, and flipping them 180 degrees? Or keeping the orientation the same and moving from left to right side? So the worn part is now on the inside.

 

 Bob

 

 --------

 Bob Turner

 RV-10 QB

 

 

 

 

 Read this topic online here:

 

 http://forums.matronics.com/viewtopic.php?p=366877#366877

rv10rob(at)gmail.com
Guest

Posted: Wed Feb 22, 2012 7:48 pm Post subject: maintenance profile

Just flipped mine at first annual, after 171 landings.  Still had some good tread on them, but decided to do it while I had it down for annual.  Almost zero wear on the other side of the tires.



 On Wed, Feb 22, 2012 at 9:19 AM, John Ackerman <johnag5b(at)cableone.net (johnag5b(at)cableone.net)> wrote:

 	  Quote: 	
		   --> RV10-List message posted by: John Ackerman <johnag5b(at)cableone.net (johnag5b(at)cableone.net)>

 

 Flipped them at inspection time - about 80 hrs. Appreciably more wear on outside.

 John Ackerman

 40458

 

 On Feb 21, 2012, at 1:24 PM, Bob Turner wrote:

 

 > --> RV10-List message posted by: "Bob Turner" <bobturner(at)alum.rpi.edu (bobturner(at)alum.rpi.edu)>

 >

 > So....is anyone removing their tires before the wear is too extreme, and flipping them 180 degrees? Or keeping the orientation the same and moving from left to right side? So the worn part is now on the inside.

 >

 > Bob

 >

 > --------

 > Bob Turner

 > RV-10 QB

 >

 >

 >

 >

 

 	  Quote: 	
		   Read this topic online here:

 >
	


 > http://forums.matronics.com/viewtopic.php?p=366877#366877

 >

 >

 >

 >

 >

 >

 >

 >

 >

 >

 

 

 

 =

 arget="_blank">http://www.matronics.com/Navigator?RV10-List

 ===========

 http://forums.matronics.com

 ===========

 le, List Admin.

 ="_blank">http://www.matronics.com/contribution

 ===========

 

 

 

 



	


-- 

Rob Kochman

RV-10 Flying since March 2011

 Woodinville, WA

 http://kochman.net/N819K



  [quote][b]

Display posts from previous:

	Matronics Email Lists Forum Index -> RV10-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum