 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
sarg314(at)gmail.com
Guest
|
 Posted: Sat Jul 07, 2012 10:14 pm Post subject: screen in sump? |
 |
|
The checklist I am using for my annual inspections says "remove, clean, inspect oil suction screen in sump". Where in an Lyc. O-360 is the oil suction sump? I have an oil filter on the engine, so don't confuse this with the engine oil screen. There is no oil screen in the engine because that was replaced with the oil filter. Is there another screen in the sump and if so how do I get to it?
Thanks,
--
Tom Sargent
[quote][b]
| | - The Matronics RV-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV-List |
|
|
|
| Back to top |
|
 |
vanremog(at)aol.com
Guest
|
| Posted: Sat Jul 07, 2012 10:57 pm Post subject: screen in sump? |
|
|
The Lycoming O-360 series suction screen is accessed by removing a hex headed cap plug on the rear near the bottom of the sump. In the PC-106 Parts Catalog please ref Figure 25 Find No. 21.
-GV
--
| | - The Matronics RV-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV-List |
|
|
|
| Back to top |
|
|
recapen(at)earthlink.net
Guest
|
| Posted: Sun Jul 08, 2012 3:53 am Post subject: screen in sump? |
|
|
Tom,
When you do find it (other post had a good description), remember to replace the crush gasket, I buy oil filters, crush gaskets and Oil analysis kits in matching batches – usually 6-pack as the oil filters come that way at a discount.
If you still can’t find it let me know and I’ll get a picture for you…
Ralph
From: owner-rv-list-server(at)matronics.com [mailto:owner-rv-list-server(at)matronics.com] On Behalf Of thomas sargent
Sent: Sunday, July 08, 2012 2:14 AM
To: rv-list
Subject: screen in sump?
The checklist I am using for my annual inspections says "remove, clean, inspect oil suction screen in sump". Where in an Lyc. O-360 is the oil suction sump? I have an oil filter on the engine, so don't confuse this with the engine oil screen. There is no oil screen in the engine because that was replaced with the oil filter. Is there another screen in the sump and if so how do I get to it?
Thanks,
--
Tom Sargent | Quote: | | http://www.matronics.com/Navigator?RV-List |
01234567
[quote][b]
| | - The Matronics RV-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV-List |
|
|
|
| Back to top |
|
|
carl.froehlich(at)verizon
Guest
|
| Posted: Sun Jul 08, 2012 5:09 am Post subject: screen in sump? |
|
|
Ralph,
What size is the crush gasket? I’m putting an Aircraft Spruce order together and I may as well get some now.
Thanks,
Carl
From: owner-rv-list-server(at)matronics.com [mailto:owner-rv-list-server(at)matronics.com] On Behalf Of Ralph E. Capen
Sent: Sunday, July 08, 2012 7:54 AM
To: rv-list(at)matronics.com
Subject: RE: screen in sump?
Tom,
When you do find it (other post had a good description), remember to replace the crush gasket, I buy oil filters, crush gaskets and Oil analysis kits in matching batches – usually 6-pack as the oil filters come that way at a discount.
If you still can’t find it let me know and I’ll get a picture for you…
Ralph
From: owner-rv-list-server(at)matronics.com (owner-rv-list-server(at)matronics.com) [mailto:owner-rv-list-server(at)matronics.com (owner-rv-list-server(at)matronics.com)] On Behalf Of thomas sargent
Sent: Sunday, July 08, 2012 2:14 AM
To: rv-list
Subject: screen in sump?
The checklist I am using for my annual inspections says "remove, clean, inspect oil suction screen in sump". Where in an Lyc. O-360 is the oil suction sump? I have an oil filter on the engine, so don't confuse this with the engine oil screen. There is no oil screen in the engine because that was replaced with the oil filter. Is there another screen in the sump and if so how do I get to it?
Thanks,
--
Tom Sargent012345678901234567
[quote][b]
| | - The Matronics RV-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV-List |
|
|
|
| Back to top |
|
|
Kellym
Joined: 10 Jan 2006
Posts: 1705
Location: Sun Lakes AZ
|
| Posted: Sun Jul 08, 2012 5:34 am Post subject: screen in sump? |
|
|
From the referenced thread,
"STD-111 Gasket, 1 in ID x 1 1/4 in ID x 3/32 Annular.
I believe it might also have an AN 900 number...
A whole 58 cents from AERO.....
http://www.aeroinstock.com/products/GASKET/5598/48371/product_detail/index.html
.also cross references to a MS35769-21 on the AERO site....
But, if it's 1.00 inch ID (and the plug has a 1.0 diam thread) then the
correct cross-reference is MS35769-16 or the older AN900-16 number - and
is a whole 39 cents from Aircraft Spruce."
On 7/8/2012 6:09 AM, Carl Froehlich wrote:
| Quote: |
Ralph,
What size is the crush gasket? I’m putting an Aircraft Spruce order
together and I may as well get some now.
Thanks,
Carl
*From:*owner-rv-list-server(at)matronics.com
[mailto:owner-rv-list-server(at)matronics.com] *On Behalf Of *Ralph E. Capen
*Sent:* Sunday, July 08, 2012 7:54 AM
*To:* rv-list(at)matronics.com
*Subject:* RE: screen in sump?
Tom,
When you do find it (other post had a good description), remember to
replace the crush gasket, I buy oil filters, crush gaskets and Oil
analysis kits in matching batches – usually 6-pack as the oil filters
come that way at a discount.
If you still can’t find it let me know and I’ll get a picture for you…
Ralph
*From:*owner-rv-list-server(at)matronics.com
<mailto:owner-rv-list-server(at)matronics.com>
[mailto:owner-rv-list-server(at)matronics.com] *On Behalf Of *thomas sargent
*Sent:* Sunday, July 08, 2012 2:14 AM
*To:* rv-list
*Subject:* screen in sump?
The checklist I am using for my annual inspections says "remove,
clean, inspect oil suction screen in sump". Where in an Lyc. O-360 is
the oil suction sump? I have an oil filter on the engine, so don't
confuse this with the engine oil screen. There is no oil screen in
the engine because that was replaced with the oil filter. Is there
another screen in the sump and if so how do I get to it?
Thanks,
--
Tom Sargent
* *
* *
* *
*http://www.matronics.com/Navigator?RV-List*
* *
*http://forums.matronics.com*
* *
*http://www.matronics.com/contribution*
* *
* *
* *
* *
**
**
**
**
**
*http://www.matronics.com/Navigator?RV-List*
**
**
*http://forums.matronics.com*
**
**
**
**
*http://www.matronics.com/contribution*
**
* *
*
*
|
| | - The Matronics RV-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV-List |
|
_________________
Kelly McMullen
A&P/IA, EAA Tech Counselor # 5286
KCHD |
|
| Back to top |
|
|
dan.pat.b(at)gmail.com
Guest
|
| Posted: Sun Jul 08, 2012 7:09 am Post subject: screen in sump? |
|
|
Tom:On a Lyc 360 it's a metal, reuseable, "finger" filter - accessed by removing a hex-head cap (the filter will come out with the cap) on the back of the engine, right side and down low - not the easiest thing to get at and difficult to safety wire when reinstalling - helps to temporarily remove SCAT tubing connecting the right side heat muff to the heater box - clean it with solvent - be careful puttting it back in - it's easily crushed if you don't fully seat it before tightening the cap. Hope this helps!
Cheers,
Dan Bergeron
RV-7A - N307TB
320 hours since
1st flight on 8/4/09
On Sun, Jul 8, 2012 at 9:32 AM, Kelly McMullen <kellym(at)aviating.com (kellym(at)aviating.com)> wrote:
[quote]--> RV-List message posted by: Kelly McMullen <kellym(at)aviating.com (kellym(at)aviating.com)>
>From the referenced thread,
"STD-111 Gasket, 1 in ID x 1 1/4 in ID x 3/32 Annular.
I believe it might also have an AN 900 number...
A whole 58 cents from AERO.....
http://www.aeroinstock.com/products/GASKET/5598/48371/product_detail/index.html
.also cross references to a MS35769-21 on the AERO site....
But, if it's 1.00 inch ID (and the plug has a 1.0 diam thread) then the correct cross-reference is MS35769-16 or the older AN900-16 number - and is a whole 39 cents from Aircraft Spruce."
On 7/8/2012 6:09 AM, Carl Froehlich wrote:
| Quote: |
Ralph,
What size is the crush gasket? I’m putting an Aircraft Spruce order together and I may as well get some now.
Thanks,
Carl
*From:*owner-rv-list-server(at)matronics.com (owner-rv-list-server(at)matronics.com) [mailto:owner-rv-list-server(at)matronics.com (owner-rv-list-server(at)matronics.com)] *On Behalf Of *Ralph E. Capen
*Sent:* Sunday, July 08, 2012 7:54 AM
*To:* rv-list(at)matronics.com (rv-list(at)matronics.com)
*Subject:* RE: screen in sump?
Tom,
When you do find it (other post had a good description), remember to replace the crush gasket, I buy oil filters, crush gaskets and Oil analysis kits in matching batches – usually 6-pack as the oil filters come that way at a discount.
If you still can’t find it let me know and I’ll get a picture for you…
Ralph
*From:*owner-rv-list-server(at)matronics.com (owner-rv-list-server(at)matronics.com) <mailto:owner-rv-list-server(at)matronics.com (owner-rv-list-server(at)matronics.com)> [mailto:owner-rv-list-server(at)matronics.com (owner-rv-list-server(at)matronics.com)] *On Behalf Of *thomas sargent
*Sent:* Sunday, July 08, 2012 2:14 AM
*To:* rv-list
*Subject:* screen in sump?
The checklist I am using for my annual inspections says "remove, clean, inspect oil suction screen in sump". Where in an Lyc. O-360 is the oil suction sump? I have an oil filter on the engine, so don't confuse this with the engine oil screen. There is no oil screen in the engine because that was replaced with the oil filter. Is there another screen in the sump and if so how do I get to it?
Thanks,
--
Tom Sargent
* *
* *
* *
*[url=http://www.matronics.com/Navigator?RV-List*]http://www.matronics.com/Navigator?RV-List*[/url]
* *
*http://forums.matronics.com*
* *
*[url=http://www.matronics.com/contribution*]http://www.matronics.com/contribution*[/url]
* *
* *
* *
* *
**
**
**
**
**
*[url=http://www.matronics.com/Navigator?RV-List*]http://www.matronics.com/Navigator?RV-List*[/url]
**
**
*http://forums.matronics.com*
**
**
**
**
*[url=http://www.matronics.com/contribution*]http://www.matronics.com/contribution*[/url]
**
* *
*
*
|
====================================
get="_blank">http://www.matronics.com/Navigator?RV-List
====================================
http://forums.matronics.com
====================================
le, List Admin.
="_blank">http://www.matronics.com/contribution
====================================
[b]
| | - The Matronics RV-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV-List |
|
|
|
| Back to top |
|
|
Paul Valovich
Joined: 11 Jan 2006
Posts: 75
|
| Posted: Sun Jul 08, 2012 8:18 am Post subject: screen in sump? |
|
|
On my IO-360 facing forward it’s the safety wired cap on the right side of the sump. Getting to it and re-safety wiring it is a PITA.
[quote][b]
| | - The Matronics RV-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV-List |
|
|
|
| Back to top |
|
|
recapen(at)earthlink.net
Guest
|
| Posted: Sun Jul 08, 2012 1:53 pm Post subject: screen in sump? |
|
|
AN900-16 AN GASKETS MS35769-21
Is what I ordered...
From: owner-rv-list-server(at)matronics.com [mailto:owner-rv-list-server(at)matronics.com] On Behalf Of Carl Froehlich
Sent: Sunday, July 08, 2012 9:09 AM
To: rv-list(at)matronics.com
Subject: RE: screen in sump?
Ralph,
What size is the crush gasket? I’m putting an Aircraft Spruce order together and I may as well get some now.
Thanks,
Carl
From: owner-rv-list-server(at)matronics.com (owner-rv-list-server(at)matronics.com) [mailto:owner-rv-list-server(at)matronics.com] ([email][mailto:owner-rv-list-server(at)matronics.com][/email]) On Behalf Of Ralph E. Capen
Sent: Sunday, July 08, 2012 7:54 AM
To: rv-list(at)matronics.com (rv-list(at)matronics.com)
Subject: RE: screen in sump?
Tom,
When you do find it (other post had a good description), remember to replace the crush gasket, I buy oil filters, crush gaskets and Oil analysis kits in matching batches – usually 6-pack as the oil filters come that way at a discount.
If you still can’t find it let me know and I’ll get a picture for you…
Ralph
From: owner-rv-list-server(at)matronics.com (owner-rv-list-server(at)matronics.com) [mailto:owner-rv-list-server(at)matronics.com (owner-rv-list-server(at)matronics.com)] On Behalf Of thomas sargent
Sent: Sunday, July 08, 2012 2:14 AM
To: rv-list
Subject: screen in sump?
The checklist I am using for my annual inspections says "remove, clean, inspect oil suction screen in sump". Where in an Lyc. O-360 is the oil suction sump? I have an oil filter on the engine, so don't confuse this with the engine oil screen. There is no oil screen in the engine because that was replaced with the oil filter. Is there another screen in the sump and if so how do I get to it?
Thanks,
--
Tom Sargent0123456789012345678901234567
[quote][b]
| | - The Matronics RV-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV-List |
|
|
|
| Back to top |
|
|
sarg314(at)gmail.com
Guest
|
| Posted: Sun Jul 08, 2012 8:13 pm Post subject: screen in sump? |
|
|
Thanks for the responses. I ordered the lyc. parts manual.
--
Tom Sargent
[quote][b]
| | - The Matronics RV-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
