 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
JAPhillipsGA(at)aol.com
Guest
|
 Posted: Thu Jun 01, 2006 6:24 am Post subject: 601XL-Jab Rubber Engine Mounts |
 |
|
Thread Friends, I have engine droop. My rubber grommets are too soft and so
it droops. My shame is unbearable. Called Jab this a.m. and they said to put in
the special washers to firm up the rubber. Anybody used these washers and is
there anything special about the locations, size or sequencing of
installation? Best regards, Bill of Georgia
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
 |
nfivesl(at)yahoo.com
Guest
|
| Posted: Thu Jun 01, 2006 7:23 am Post subject: 601XL-Jab Rubber Engine Mounts |
|
|
Bill:
You should use the little blue washers from "Pfizer
Engine Noncertified Industrial Services." Here's a
snippet from their website:
"VIAGRAWASHERS (The Little Blue Washers) are the #1
prescribed washers for the condition known as ED
(Engine Droop). VIAGRAWASHERS have been used by over 9
million A&P's and Pilots for the treatment of engine
droop (ED, also called engine-impotence).
There's no need for shame.
Scott Laughlin
www.cooknwithgas.com
Do Not Archive (please)
--- JAPhillipsGA(at)aol.com wrote:
| Quote: |
Thread Friends, I have engine droop. My rubber
grommets are too soft and so
it droops. My shame is unbearable.
|
__________________________________________________
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
larry(at)macsmachine.com
Guest
|
| Posted: Thu Jun 01, 2006 8:56 am Post subject: 601XL-Jab Rubber Engine Mounts |
|
|
Bill,
I had to lower the prop centerline a degree and put aluminum spacer
washers between the mount and
the rubber washers. It worked to get the droop I wanted, so it follows
you might be able to get the same
result in the reverse by putting them on the bottom mounts.
Larry McFarland - 601HDS at www.macsmachine.com
do not archive
APhillipsGA(at)aol.com wrote:
| Quote: |
Thread Friends, I have engine droop. My rubber grommets are too soft and so
it droops. My shame is unbearable. Called Jab this a.m. and they said to put in
the special washers to firm up the rubber. Anybody used these washers and is
there anything special about the locations, size or sequencing of
installation? Best regards, Bill of Georgia
|
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
noelloveys(at)yahoo.ca
Guest
|
| Posted: Thu Jun 01, 2006 2:12 pm Post subject: 601XL-Jab Rubber Engine Mounts |
|
|
lol
Noel
[quote] --
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
JAPhillipsGA(at)aol.com
Guest
|
| Posted: Fri Jun 02, 2006 5:16 am Post subject: 601XL-Jab Rubber Engine Mounts |
|
|
Larry, thanks, I'll try that. Have you noticed any splitting of the rubber
bushing ? I was told by an a & p to be concerned about that if a washer is used
to adjust the engine angle. Best regards, Bill
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
JAPhillipsGA(at)aol.com
Guest
|
| Posted: Fri Jun 02, 2006 5:18 am Post subject: 601XL-Jab Rubber Engine Mounts |
|
|
Scott, I'll see if the blue washers are covered in my HMO. Best to you, Bill
do not archive
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
larry(at)macsmachine.com
Guest
|
| Posted: Fri Jun 02, 2006 6:57 am Post subject: 601XL-Jab Rubber Engine Mounts |
|
|
Bill,
No splitting of the bushings at all. If this occurs, I believe the
rubber has aged beyond its useful
life and would replace them.
Larry
JAPhillipsGA(at)aol.com wrote:
| Quote: |
Larry, thanks, I'll try that. Have you noticed any splitting of the rubber
bushing ? I was told by an a & p to be concerned about that if a washer is used
to adjust the engine angle. Best regards, Bill
|
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
