Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

CH601-HD baggage floor

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Zenith-List
View previous topic :: View next topic  
Author Message
carlossa52(at)gmail.com
Guest





PostPosted: Mon Oct 29, 2012 6:09 pm    Post subject: CH601-HD baggage floor Reply with quote

Hello gang (assuming you are still out there...?)I am doing a trial fitting of the (CH601-HD) baggage floor. So far, everything fits nicely, rear fuse to centre wing, firewall, alignment, etc. I am a bit puzzled by the baggage floor: it seems to be about 20 - 25 mm (one inch or so) too long: according to the plans, the baggage floor should end at the continuation of the seat's back (or 6F13-3, same thing).
Did any of the HD(S) builders out there have to trim the from edge of the baggage floor?
I did a search of the archives, but did not find a similar case...�
Actually, I found someone's post talking about a "perfect fit" (i.e., trim required only to fit the longeron curve).

Comments/suggestions?

(PS: hope everyone is safe out there.)

Thanks
Carlos
CH601-HD, plans
rear fuse, centre wing, firewall in place


[quote][b]


- The Matronics Zenith-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List
Back to top
 
carlossa52(at)gmail.com
Guest





PostPosted: Mon Oct 29, 2012 6:34 pm    Post subject: CH601-HD baggage floor Reply with quote

Here's a picture, might help explain the situation.

On 29 October 2012 22:07, Carlos Sa <carlossa52(at)gmail.com (carlossa52(at)gmail.com)> wrote:
Quote:
Hello gang (assuming you are still out there...?) I am doing a trial fitting of the (CH601-HD) baggage floor. So far, everything fits nicely, rear fuse to centre wing, firewall, alignment, etc. I am a bit puzzled by the baggage floor: it seems to be about 20 - 25 mm (one inch or so) too long: according to the plans, the baggage floor should end at the continuation of the seat's back (or 6F13-3, same thing).
Did any of the HD(S) builders out there have to trim the from edge of the baggage floor?
I did a search of the archives, but did not find a similar case...�
Actually, I found someone's post talking about a "perfect fit" (i.e., trim required only to fit the longeron curve).

Comments/suggestions?

(PS: hope everyone is safe out there.)

Thanks
Carlos
CH601-HD, plans
rear fuse, centre wing, firewall in place


Quote:


arget="_blank">http://www.matronics.com/Navigator?Zenith-List
tp://forums.matronics.com
_blank">http://www.matronics.com/contribution



- The Matronics Zenith-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List



baggage_floor.jpg
 Description:
 Filesize:  139.28 KB
 Viewed:  2974 Time(s)

baggage_floor.jpg


Back to top
 
jlatimer1(at)cox.net
Guest





PostPosted: Tue Oct 30, 2012 7:33 am    Post subject: CH601-HD baggage floor Reply with quote

Carlos,

I don't recall having to trim 6F13-3. I reviewed my building log and photos from that time and there were no notes about having to trim 25mm from the front edge.

Jerry

From: owner-zenith-list-server(at)matronics.com [mailto:owner-zenith-list-server(at)matronics.com] On Behalf Of Carlos Sa
Sent: Monday, October 29, 2012 7:08 PM
To: zenith-list(at)matronics.com
Subject: CH601-HD baggage floor

Hello gang (assuming you are still out there...?)I am doing a trial fitting of the (CH601-HD) baggage floor. So far, everything fits nicely, rear fuse to centre wing, firewall, alignment, etc.I am a bit puzzled by the baggage floor: it seems to be about 20 - 25 mm (one inch or so) too long: according to the plans, the baggage floor should end at the continuation of the seat's back (or 6F13-3, same thing).
Did any of the HD(S) builders out there have to trim the from edge of the baggage floor?
I did a search of the archives, but did not find a similar case...
Actually, I found someone's post talking about a "perfect fit" (i.e., trim required only to fit the longeron curve).

Comments/suggestions?

(PS: hope everyone is safe out there.)

Thanks
Carlos
CH601-HD, plans
rear fuse, centre wing, firewall in place

[quote][b]


- The Matronics Zenith-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List
Back to top
 
carlossa52(at)gmail.com
Guest





PostPosted: Tue Oct 30, 2012 7:50 am    Post subject: CH601-HD baggage floor Reply with quote

Thanks, Jerry - It seems I am in a unusual situation.Maybe the seat back angle is off... I sent a note to ZAC, as this could be a symptom of some major issue.. Carlos

On 30 October 2012 11:32, Jerry Latimer <jlatimer1(at)cox.net (jlatimer1(at)cox.net)> wrote:
[quote] Carlos,

I don't recall having to trim 6F13-3.� I reviewed my building log and photos from that time and there were no notes about having to trim 25mm from the front edge.

Jerry

From: owner-zenith-list-server(at)matronics.com (owner-zenith-list-server(at)matronics.com) [mailto:owner-zenith-list-server(at)matronics.com (owner-zenith-list-server(at)matronics.com)] On Behalf Of Carlos Sa
Sent: Monday, October 29, 2012 7:08 PM
To: zenith-list(at)matronics.com (zenith-list(at)matronics.com)
Subject: CH601-HD baggage floor

Hello gang (assuming you are still out there...?)I am doing a trial fitting of the (CH601-HD) baggage floor. So far, everything fits nicely, rear fuse to centre wing, firewall, alignment, etc.I am a bit puzzled by the baggage floor: it seems to be about 20 - 25 mm (one inch or so) too long: according to the plans, the baggage floor should end at the continuation of the seat's back (or 6F13-3, same thing).
Did any of the HD(S) builders out there have to trim the from edge of the baggage floor?
I did a search of the archives, but did not find a similar case...�
Actually, I found someone's post talking about a "perfect fit" (i.e., trim required only to fit the longeron curve).

Comments/suggestions?

(PS: hope everyone is safe out there.)

Thanks
Carlos
CH601-HD, plans
rear fuse, centre wing, firewall in place

Quote:


arget="_blank">http://www.matronics.com/Navigator?Zenith-List
tp://forums.matronics.com
_blank">http://www.matronics.com/contribution


[b]


- The Matronics Zenith-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List
Back to top
 
jlatimer1(at)cox.net
Guest





PostPosted: Tue Oct 30, 2012 8:06 am    Post subject: CH601-HD baggage floor Reply with quote

Carlos,
When I go to the airport next, I will measure the baggage floor and see if I've removed some material from it. I know I had to make some modifications to rear turtle deck when I installed the front opening canopy, but I don't think I had to trim the baggage floor.
Jerry

From: owner-zenith-list-server(at)matronics.com [mailto:owner-zenith-list-server(at)matronics.com] On Behalf Of Carlos Sa
Sent: Tuesday, October 30, 2012 8:49 AM
To: zenith-list(at)matronics.com
Subject: Re: CH601-HD baggage floor

Thanks, Jerry - It seems I am in a unusual situation.Maybe the seat back angle is off... I sent a note to ZAC, as this could be a symptom of some major issue...Carlos

On 30 October 2012 11:32, Jerry Latimer <jlatimer1(at)cox.net (jlatimer1(at)cox.net)> wrote:
[quote] Carlos,

I don't recall having to trim 6F13-3. I reviewed my building log and photos from that time and there were no notes about having to trim 25mm from the front edge.

Jerry

From: owner-zenith-list-server(at)matronics.com (owner-zenith-list-server(at)matronics.com) [mailto:owner-zenith-list-server(at)matronics.com (owner-zenith-list-server(at)matronics.com)] On Behalf Of Carlos Sa
Sent: Monday, October 29, 2012 7:08 PM
To: zenith-list(at)matronics.com (zenith-list(at)matronics.com)
Subject: Zenith-List: CH601-HD baggage floor

Hello gang (assuming you are still out there...?)I am doing a trial fitting of the (CH601-HD) baggage floor. So far, everything fits nicely, rear fuse to centre wing, firewall, alignment, etc.I am a bit puzzled by the baggage floor: it seems to be about 20 - 25 mm (one inch or so) too long: according to the plans, the baggage floor should end at the continuation of the seat's back (or 6F13-3, same thing).
Did any of the HD(S) builders out there have to trim the from edge of the baggage floor?
I did a search of the archives, but did not find a similar case...
Actually, I found someone's post talking about a "perfect fit" (i.e., trim required only to fit the longeron curve).

Comments/suggestions?

(PS: hope everyone is safe out there.)

Thanks
Carlos
CH601-HD, plans
rear fuse, centre wing, firewall in place

Quote:


arget="_blank">http://www.matronics.com/Navigator?Zenith-List
tp://forums.matronics.com
_blank">http://www.matronics.com/contribution




href="http://www.matronics.com/Navigator?Zenith-List">http://www.matronhref="http://forums.matronics.com">http://forums.matronics.com
href="http://www.matronics.com/contribution">http://www.matronics.com/c
[b]


- The Matronics Zenith-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List
Back to top
 
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Zenith-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group