 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
Ed Godfrey
Joined: 05 May 2009
Posts: 47
|
 Posted: Sun Nov 11, 2012 8:37 am Post subject: Opinions please |
 |
|
Well, I have applied flame to it and also tried sanding it to see if the
edges show. Both were negative, so I will continue sanding it and
filling where necessary. Thanks to all for your advice and suggestions.
Ed Godfrey
40717
On 11/3/2012 6:49 PM, Dave Saylor wrote:
Bill's right, that's most likely an area that never had peel-ply over
it. If it does turn out to still have some on it, you should be able to
get ahold of an edge and tear it off. In that area, it wouldn't hurt to
just leave some peel ply there but that's not really the best practice.
It looks to me like it's just plain glass though.
I'd sand it with some 80 grit and finish it however you like. That's
another way to find the peel ply--if the edges ball up when you sand it,
you'll know it's peel-ply.
I painted some of those hard-to-finish areas with truck bed liner.
Turned out pretty well.
Dave Saylor
831-750-0284 CL
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
 |
davidsoutpost(at)comcast.
Guest
|
| Posted: Sun Nov 11, 2012 8:51 am Post subject: Opinions please |
|
|
Its just glass that wasn't peel plied. You would immediately see the fibers of the peel ply show up white after you hit it with some course 36 or 40 sand paper. Clean the area up to your satisfaction and move on.
David Clifford
RV-10 Builder
Howell, MI
From: "Ed Godfrey" <egodfrey(at)ameritech.net>
To: "RV-10 List" <rv10-list(at)matronics.com>
Sent: Sunday, November 11, 2012 11:37:00 AM
Subject: Opinions please
--> RV10-List message posted by: Ed Godfrey <egodfrey(at)ameritech.net>
Well, I have applied flame to it and also tried sanding it to see if the
edges show. Both were negative, so I will continue sanding it and
filling where necessary. Thanks to all for your advice and suggestions.
Ed Godfrey
40717
On 11/3/2012 6:49 PM, Dave Saylor wrote:
Bill's right, that's most likely an area that never had peel-ply over
it. If it does turn out to still have some on it, you should be able to
get ahold of an edge and tear it off. In that area, it wouldn't hurt to
just leave some peel ply there but that's not really the best practice.
It looks to me like it's just plain glass though.
I'd sand it with some 80 grit and finish it however you like. That's
another way to find the peel ply--if the edges ball up when you sand it,
you'll know it's peel-ply.
I painted some of those hard-to-finish areas with truck bed liner.
Turned out pretty well.
Dave Sbsp; ==
[quote][b]
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
