Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

912 carb cable ends

Matronics Email Lists Forum Index -> RotaxEngines-List

View previous topic :: View next topic

Author Message

Roland Smith

Joined: 02 Jul 2006
Posts: 14

Posted: Tue May 13, 2008 5:16 am Post subject: 912 carb cable ends

Help.  The carburetor cable ends I got from SkyShop with my 701 FWF package are too large to fit the holes in the 912 carb levers and it is almost impossible to reduce them for a good fit.  Skyshop 701  FWF is no longer supported by their supplier.



 Where can I get cables with proper ends ?  The item is not shown in the Rotax 912 parts diagram, just the carb levers into which it fits.



Do not archive.



Roland Smith,  Bennington, Vermont

- The Matronics RotaxEngines-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RotaxEngines-List

_________________
701 kit, Rotax 912 ULS, SensorNetics EFIS, Flying.

Float Flyr

Joined: 19 Jul 2006
Posts: 2704
Location: Campbellton, Newfoundland

Posted: Tue May 13, 2008 6:35 am Post subject: 912 carb cable ends

Can you change the holes on your carb levers?



Noel



--

- The Matronics RotaxEngines-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RotaxEngines-List

_________________
Noel Loveys
Kitfox III-A
Aerocet 1100 Floats

jswanson(at)jamadots.com
Guest

Posted: Tue May 13, 2008 9:30 am Post subject: 912 carb cable ends

---

- The Matronics RotaxEngines-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RotaxEngines-List

Catz631(at)aol.com
Guest

Posted: Wed May 14, 2008 3:21 am Post subject: 912 carb cable ends

I just replaced my throttle cables in my 912 yesterday. I used cable stock I purchased from Lockwood when I attended the 912 school in Jan. I bought a cable cutter and clipped the ends of the cable and housing to proper size slid thru the "bug nuts' on the carb and the throttles. You could then put shrink tubing over the cable ends to discourage fraying (or solder,or rubber dip)

   That is how I did it on my Kitfox and how it appeared to be done on the CT's they were flying at Lockwood. When we were doing the carb sync ,I took a good look at the throttle cable routing. It is rather a pain to get the cable thru the small holes.Make sure you use a good cable cutter ! Lockwood has real nice reusable cable  end retainers/adjusters for about $4.00 ea. They were far nicer then the old crimped ends on my 2001 Rotax 912 engine.

     I am sure your engine probably uses a different setup (my luck) but that is how I did mine. 

     Today I will pneumatically sync the carbs in about 1 minute with my " throttle bug" and my Twin Max carb sync system. What a nice easy system !

                                                                           

                                                                                             Dick Maddux

                                                                                             Fox4-1200

                                                                                             Rotax 912UL

                                                                                             Pensacola,Fl (starting to get hot ! Yeeechhhh! ) 

  



Wondering what's for Dinner Tonight? Get new twists on family favorites at AOL Food.

  [quote][b]

- The Matronics RotaxEngines-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RotaxEngines-List

Catz631(at)aol.com
Guest

Posted: Wed May 14, 2008 4:06 am Post subject: 912 carb cable ends

Roland,

    Here is a picture of a CT carb I snapped at Lockwood showing the linkage. It has the "super deluxe" adjustable cable ends and shows the threading of the cable I was talking about.

                                                Dick Maddux

  

  

  

  

  

  

  



Wondering what's for Dinner Tonight? Get new twists on family favorites at AOL Food.

- The Matronics RotaxEngines-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RotaxEngines-List

Kitfox_020.jpg

Description:

Filesize:

369.33 KB

Viewed:

545 Time(s)

Display posts from previous:

	Matronics Email Lists Forum Index -> RotaxEngines-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum