Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Static Line Route

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV9-List
View previous topic :: View next topic  
Author Message
Bob Perkinson



Joined: 10 Jan 2006
Posts: 51
Location: Hendersonville, Tennessee
PostPosted: Tue Jan 06, 2009 11:05 am    Post subject: Static Line Route Reply with quote
Group,
Where exactly did you rout the static line through bulkhead F5 (seat back bulkhead)? I am at the point or running the static line and have it up under the longeron, the way I see it the 7/16" hole needed to run the line would need to be placed some where well below the rivet group holding the F5 doubler, putting a 2" water trap in the line. Does this sag even matter? If the hole is drilled high on F5 it looks like the edge distance on the rivets would be violated.
If any one has photos of this area, that would be nice.
Bob Perkinson

- The Matronics RV9-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV9-List
Back to top
View user's profile Send private message Send e-mail
wowens(at)darientel.net
Guest
PostPosted: Tue Jan 06, 2009 1:46 pm    Post subject: Static Line Route Reply with quote
An RVator from about two years ago has a picture.
---

- The Matronics RV9-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV9-List
Back to top
Bill Chenoweth



Joined: 10 Jul 2008
Posts: 9
PostPosted: Tue Jan 06, 2009 2:33 pm    Post subject: Static Line Route Reply with quote
Thanks - I was just about to ask you for her name again. Looks like the
project is going forward.
---

- The Matronics RV9-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV9-List
Back to top
View user's profile Send private message Send e-mail
Bill Chenoweth



Joined: 10 Jul 2008
Posts: 9
PostPosted: Tue Jan 06, 2009 3:25 pm    Post subject: Static Line Route Reply with quote
Sorry folks - slip of the "response" finger with the "project is going
forward" thing.

However, Bob, regarding your static line routing. As mentioned, the RVator
has an article but as I recall there were some labeling errors in the
captions or such. I did mine the way the article suggested and am still
pretty much wide open in the fuselage department so I can send pictures if
you want.
Bill
---

- The Matronics RV9-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV9-List
Back to top
View user's profile Send private message Send e-mail
Bob Perkinson



Joined: 10 Jan 2006
Posts: 51
Location: Hendersonville, Tennessee
PostPosted: Tue Jan 06, 2009 3:47 pm    Post subject: Static Line Route Reply with quote


- The Matronics RV9-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV9-List
Back to top
View user's profile Send private message Send e-mail
bmrv09(at)hotmail.com
Guest
PostPosted: Tue Jan 06, 2009 5:37 pm    Post subject: Static Line Route Reply with quote
I have an rv6a C but I run mine C right under the longeron C all the way C then along horizontally to the insturment pannel..
I use plastic C stand offs C  glue with proseal C C alongl the way to hold plastic line C with tie wraps.. Acutally you do not need that..
 
Robert
 


[quote] From: wowens(at)darientel.net
To: rv9-list(at)matronics.com
Subject: Re: Static Line Route
Date: Tue C 6 Jan 2009 16:42:48 -0500

--> RV9-List message posted by: "Wayne" <wowens(at)darientel.net>

An RVator from about two years ago has a picture.
---

- The Matronics RV9-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV9-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV9-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group