 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
smgores
Joined: 11 Jan 2006
Posts: 7
|
 Posted: Tue Feb 16, 2010 7:33 pm Post subject: aileron trim servo angles |
 |
|
Fellow builders;
The upgrade drawings,6-ZU-4,shows the L angles for the aileron trim servos as being 265 mm long,on the plans dated 25 Jan 2010.As I measure mine,the longest they can be is approx. 220mm.,if you extend them onto the piano hinge flange and past the front of the servo on the 20 mm flange of the skin.Or,185mm. if you don't lap the 2 surfaces.Has anyone dealt with this yet or asked at Zenith?
I thought I would start out with a simple task to start(instead of the spars)but wouldn't you know it...?
Thank You,
MIke
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
 |
Ron Lendon
Joined: 10 Jan 2006
Posts: 685
Location: Clinton Twp., MI
|
| Posted: Tue Feb 16, 2010 9:06 pm Post subject: Re: aileron trim servo angles |
|
|
Hey Mike,
I did that to Jim's aileron and followed the guidance given in Section 6-ZU-4, Page 5 of 23.
I can take a closer look but I think the L-angles are cut to fit whatever dimension "Cut two L Angles to fit in the Aileron."
Let me know,
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
_________________
Ron Lendon
WW Corvair with Roy's Garage 5th bearing
CH 601 XLB
N601LT - Flying
http://www.mykitlog.com/rlendon
Corvair Engine Prints:
https://sites.google.com/site/corvairenginedata/ |
|
| Back to top |
|
|
Louie928
Joined: 15 Nov 2009
Posts: 32
Location: Mosier, OR USA
|
| Posted: Tue Feb 16, 2010 10:14 pm Post subject: Re: aileron trim servo angles |
|
|
I let the ends of the L angle go under the skin and trim tab piano hinge on both ends of the L angle. Since the skin was only 0.016" , I wanted some extra stiffness at the end of the L angle. It ended up looking like this. The angle is bent out a little so the edge won't catch on the servo wire when it is fit together.
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
| Description: |
|
| Filesize: |
68.39 KB |
| Viewed: |
4310 Time(s) |
|
_________________
Louis W. Ott
601XL-B Corvair |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
