Matronics Email Lists :: View topic - Seeing Matronics List Attachments

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Seeing Matronics List Attachments

Matronics Email Lists Forum Index -> KIS-List

View previous topic :: View next topic

Author Message

bakerocb

Joined: 15 Jan 2006
Posts: 727
Location: FAIRFAX VA

Posted: Sun Jun 13, 2010 5:13 am Post subject: Seeing Matronics List Attachments

---

- The Matronics KIS-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?KIS-List

bakerocb

Joined: 15 Jan 2006
Posts: 727
Location: FAIRFAX VA

Posted: Mon Jun 21, 2010 3:54 am Post subject: Seeing Matronics List Attachments

6/21/2010



Hello Fellow KIS Listers, I wrote: " PS: There is sort of a gotcha. I posted 

a jpg picture on the KIS list (see here I hope):

 	  Quote: 	
		  

 http://forums.matronics.com/viewtopic.php?t=71560



 and the picture posted just fine except that its layout on the forum was

 so huge such that one had to scroll all over the place to find the area of

 interest."


	


I have modified (shrunk) the original posted vortex generator picture 

significantly. Please see if this attached view is better for you.



Thanks,



'OC' Baker Says: "The best investment we can make is the time and effort to 

gather and understand knowledge."

- The Matronics KIS-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?KIS-List

100_0344.jpg

Description:

Filesize:

189.87 KB

Viewed:

3924 Time(s)

ftyoder(at)yoderbuilt.com
Guest

Posted: Mon Jun 21, 2010 6:04 am Post subject: Seeing Matronics List Attachments

'OC',



What are your test results? ( On the vortex generator. )



Tim



---

- The Matronics KIS-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?KIS-List

lgdavid(at)roadrunner.com
Guest

Posted: Mon Jun 21, 2010 2:09 pm Post subject: Seeing Matronics List Attachments

OC, you can shrink the display of the picture by  holding the control key down and pressing the minus key a couple of  times. (This works in Firefox and I assume other browsers.) Of course  the accompanying text will shrink also.  It looks like the device is about  6-8 inches in front of the leading edge of the tail and the device itself is  about 6-8 inches long.  Am I guessing right on the sizing?   Larry

On 6/21/2010 4:53:24 AM, bakerocb(at)cox.net (bakerocb(at)cox.net) wrote:

[quote]  6/21/2010

 Hello Fellow KIS Listers, I wrote: " PS: There is  sort of a gotcha. I posted

 a jpg picture on the KIS list (see here I  hope):

 >

 > http://forums.matronics.com/viewtopic.php?t=71560

  >

 > and the picture posted just fine except that its layout on the  forum was

 > so huge such that one had to scroll all over the place to  find the area of

    	  Quote: 	
		  [b]

- The Matronics KIS-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?KIS-List

bakerocb

Joined: 15 Jan 2006
Posts: 727
Location: FAIRFAX VA

Posted: Mon Jun 21, 2010 7:24 pm Post subject: Seeing Matronics List Attachments

6/21/2010



Hello Larry, Thanks for the picture tip.



These vortex generators go on each side of the fuselage in front of the 

wing. Their purpose is to generate higher energy air in the area of the wing 

to fuselage juncture.



They are more on the order of 4 inches long -- that is all the aluminum 

angle that I had available.



Take a look at the ones on the Cirrus airplanes to see what I am trying to 

replicate.



'OC' Baker Says: "The best investment we can make is the time and effort to 

gather and understand knowledge."



===============================================

---

- The Matronics KIS-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?KIS-List

Display posts from previous:

	Matronics Email Lists Forum Index -> KIS-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum