 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
cpayne(at)joimail.com
Guest
|
 Posted: Mon Apr 23, 2012 11:55 am Post subject: Torque values |
 |
|
Installing an OH'd M-14P which came with new rubber cushions in the mount. Does anyone know if there is a published torque value? So far I tightened the nuts until the mounts were compressed some. Took about 50 in-lbs.
Craig Payne
| | - The Matronics Yak-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Yak-List |
|
|
|
| Back to top |
|
 |
dsavarese0812(at)bellsout
Guest
|
| Posted: Mon Apr 23, 2012 12:03 pm Post subject: Torque values |
|
|
Craig,
See attached. This should answer your question.
Dennis
A. Dennis Savarese
334-285-6263
334-546-8182 (mobile)
www.yak-52.com
Skype - Yakguy1
On 4/23/2012 2:51 PM, Cpayne wrote:
| Quote: |
Installing an OH'd M-14P which came with new rubber cushions in the mount. Does anyone know if there is a published torque value? So far I tightened the nuts until the mounts were compressed some. Took about 50 in-lbs.
Craig Payne
|
| | - The Matronics Yak-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Yak-List |
|
| Description: |
|
Download |
| Filename: |
ENGINE_DAMPER_MOUNT_INSTALATION_Model.pdf |
| Filesize: |
29.25 KB |
| Downloaded: |
224 Time(s) |
| Description: |
|
Download |
| Filename: |
DAMPER_SECTION_A-A_Model_(1).pdf |
| Filesize: |
22.8 KB |
| Downloaded: |
435 Time(s) |
|
|
| Back to top |
|
|
viperdoc(at)mindspring.co
Guest
|
| Posted: Mon Apr 23, 2012 1:03 pm Post subject: Torque values |
|
|
That's what I did to mine. Nice pdf. file Dennis. Some work went into that! Maybe I missed it but where were the torque values. I'm looking for the torque values for the motor mounts on the ring and the fire wall. Right now I am using the Deutch values...goottentight.
Doc
--
| | - The Matronics Yak-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Yak-List |
|
|
|
| Back to top |
|
|
dsavarese0812(at)bellsout
Guest
|
| Posted: Mon Apr 23, 2012 1:47 pm Post subject: Torque values |
|
|
There actually are no specific torque values. It is a compression
value. IE: the dimension of the mount rubber once compressed.
Dennis
A. Dennis Savarese
334-285-6263
334-546-8182 (mobile)
www.yak-52.com
Skype - Yakguy1
On 4/23/2012 3:59 PM, Roger Kemp wrote:
[quote]
That's what I did to mine. Nice pdf. file Dennis. Some work went into that! Maybe I missed it but where were the torque values. I'm looking for the torque values for the motor mounts on the ring and the fire wall. Right now I am using the Deutch values...goottentight.
Doc
--
| | - The Matronics Yak-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Yak-List |
|
|
|
| Back to top |
|
|
viperdoc(at)mindspring.co
Guest
|
| Posted: Mon Apr 23, 2012 4:53 pm Post subject: Torque values |
|
|
Copy.. That is what I did. The T.O.'s did not give any guidance.
Doc
Sent from my iPad
On Apr 23, 2012, at 4:45 PM, "A. Dennis Savarese" <dsavarese0812(at)bellsouth.net> wrote:
[quote]
There actually are no specific torque values. It is a compression value. IE: the dimension of the mount rubber once compressed.
Dennis
A. Dennis Savarese
334-285-6263
334-546-8182 (mobile)
www.yak-52.com
Skype - Yakguy1
On 4/23/2012 3:59 PM, Roger Kemp wrote:
>
>
> That's what I did to mine. Nice pdf. file Dennis. Some work went into that! Maybe I missed it but where were the torque values. I'm looking for the torque values for the motor mounts on the ring and the fire wall. Right now I am using the Deutch values...goottentight.
> Doc
>
>
> --
| | - The Matronics Yak-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Yak-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
