Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Terminal ID?

Matronics Email Lists Forum Index -> AeroElectric-List

View previous topic :: View next topic

Author Message

donjohnston

Joined: 13 Dec 2009
Posts: 231

Posted: Sun Sep 08, 2013 5:49 am Post subject: Terminal ID?

I'm hooking up the the CHT/EGT probes to my Grand Rapids EIS. I had a couple bad crimps on the male spade connectors but I didn't have enough spares. GR sent me some extras but they changed to a different style and those don't work in my AMP 47386-R crimping tool.



I've poked around on Mouser, but all I can find are ring and butt splice. No luck on tabs.



Any suggestions on a PN?

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

569a.jpg

Description:

Filesize:

158.87 KB

Viewed:

1883 Time(s)

Kellym

Joined: 10 Jan 2006
Posts: 1705
Location: Sun Lakes AZ

Posted: Sun Sep 08, 2013 7:16 am Post subject: Terminal ID?

Probes do seem to have varying connectors. Those for EI probes have a 

bit of a bump in the middle but both male and female are fast-on fully 

insulated.

On Dynon the insulation is rounder, and the male spades do not have 

insulation over the spade, just the crimp area. I have had some luck 

matching up what I needed for extras at either Radio Shack or Home 

Depot, just being careful to only select ones with translucent nylon 

insulation, not opaque vinyl.

Haven't run into ones that don't use same crimp as any other ring or 

fast-on terminal. Seems odd that they would supply a connector that 

doesn't use a standard crimp.



On 9/8/2013 6:49 AM, donjohnston wrote:

 	  Quote: 	
		   



 I'm hooking up the the CHT/EGT probes to my Grand Rapids EIS. I had a couple bad crimps on the male spade connectors but I didn't have enough spares. GR sent me some extras but they changed to a different style and those don't work in my AMP 47386-R crimping tool.



 I've poked around on Mouser, but all I can find are ring and butt splice. No luck on tabs.



 Any suggestions on a PN?





 Read this topic online here:



 http://forums.matronics.com/viewtopic.php?p=408229#408229





 Attachments:



 http://forums.matronics.com//files/569a_158.jpg

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

_________________
Kelly McMullen
A&P/IA, EAA Tech Counselor # 5286
KCHD

Display posts from previous:

	Matronics Email Lists Forum Index -> AeroElectric-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum