Matronics Email Lists :: View topic - LED Light for SD-8 On Indication

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

LED Light for SD-8 On Indication

Matronics Email Lists Forum Index -> AeroElectric-List

View previous topic :: View next topic

Author Message

rossmickey(at)comcast.net
Guest

Posted: Sun Jun 07, 2015 4:57 pm Post subject: LED Light for SD-8 On Indication

I wanted to install an LED "ON" indicator light for when I switch on the SD-8 alternate power supply.  I rigged an LED so it works with the 12 Volt system and tried it on the switch which goes to ground for ON.  It works fine when it is the only thing on the switch.  When I hook up the SD-8 relay to it ( as wired for the original Z-8 diagram with NO self excite) which is also a switch to ground for on, the LED lights up even in the off position.  Since the LED ground and SD-8 relay ground share the same terminal, my only explanation is that the LED is finding a ground somewhere along the SD-8 relay pathway.  I have stared at the drawing until my eyes are crossed and can't figure out what's happening.



Is my SD-8 wiring screwed up or is there actually a way for the LED to find a ground along the pathway?  If so, I guess I am SOL on hooking an on indicator light.



Ross

 [quote][b]

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

user9253

Joined: 28 Mar 2008
Posts: 1921
Location: Riley TWP Michigan

Posted: Sun Jun 07, 2015 7:09 pm Post subject: Re: LED Light for SD-8 On Indication

Can you attach a drawing of your schematic showing how the LED is wired?  I can not visualize how the LED is connected.  LEDs require very little current to illuminate.  Sometimes a solid state switch (when off) will leak enough current to turn on an LED.  A schematic will be very helpful to others who are trying to answer your question.

Joe

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

_________________
Joe Gores

nuckolls.bob(at)aeroelect
Guest

Posted: Mon Jun 08, 2015 4:59 am Post subject: LED Light for SD-8 On Indication

At 07:54 PM 6/7/2015, you wrote:



 I wanted to install an LED "ON" indicator light for when I switch on the SD-8 alternate power supply.  I rigged an LED so it works with the 12 Volt system and tried it on the switch which goes to ground for ON.  It works fine when it is the only thing on the switch.  When I hook up the SD-8 relay to it ( as wired for the original Z-8 diagram with NO self excite) which is also a switch to ground for on, the LED lights up even in the off position.  Since the LED ground and SD-8 relay ground share the same terminal, my only explanation is that the LED is finding a ground somewhere along the SD-8 relay pathway.  I have stared at the drawing until my eyes are crossed and can't figure out what's happening.



    If I am interpreting your narrative correctly,

    then for some reason, there is a 'sneak path'

    to ground with the switch open. One fix for

    this phenomenon is to add a diode in the relay

    control lead that breaks sneak-path to ground

    looking at the relay.

  [img]cid:7.1.0.9.0.20150608075201.01f02418(at)aeroelectric.com.0[/img] 



   The 64 dollar question is where the sneak-path

   is coming from. As shown, I too am unable to

   identify the problem . . . UNLESS . . . your

   SD-8 is not tied to the always-hot side of

   the battery but instead tied to the switched

   side and is finding a sneak path through the

   system components on the main bus.



 

   Bob . . .

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

276eefc.jpg

Description:

Filesize:

60.01 KB

Viewed:

2582 Time(s)

rossmickey(at)comcast.net
Guest

Posted: Mon Jun 08, 2015 6:48 am Post subject: LED Light for SD-8 On Indication

I followed an article Jim Weir wrote back in 2000 for Kitplanes. 



http://www.rst-engr.com/kitplanes/KP0009A/KPtext.doc



http://www.rst-engr.com/kitplanes/KP0009A/KP0009A.htm



I know the switch is not leaking because the light works as intended when it

is hooked up to the switch by itself.  It is only when I connect the wire

that goes to the SD-8 relay that the light turns on apparently finding a

ground pathway through that system.



Ross



--

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

Display posts from previous:

	Matronics Email Lists Forum Index -> AeroElectric-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum